AGILENT 11713A ATTENUATOR SWITCH WINDOWS 10 DRIVER

AGILENT 11713A ATTENUATOR SWITCH DRIVER DETAILS:

Type: Driver
File Name: agilent_11713a_32171.zip
File Size: 25.8 MB
Rating:
4.12
77 (4.12)
Downloads: 52
Supported systems: Windows All
Price: Free* (*Free Registration Required)

Download Now
AGILENT 11713A ATTENUATOR SWITCH DRIVER



Reinstall the board carefully.

HP Agilent Keysight A attenuator/switch driver -

Switch the power on. Manually press the attenuator buttons several times. If the manual verification is satisfactory, check the computer-controlled remote operation by sending these commands. If the responses satisfactory, theA2 drive assembly should be operational.

I f the response is unsatisfactory, check the other assembi ies fi rst before you decide to replacethe A2 driver assembly. One transistor of each pair, for example, Q9 and Q18, is in saturation whilethe other transistor is in cutoff. The driver transistors each have a metal tab that is attached to a common heat sink. The relay contacts are also protected against spikes from inductive loads. To T roubleshoot the A3 Latch Assembly 1. If any of thefollowing conditions cannot be met, replacethe A3 latch assembly. Turn the power off and then turn it on again. All attenuator lights agilent 11713a attenuator switch the local light should be on.

AGILENT 11713A ATTENUATOR SWITCH DRIVERS WINDOWS XP

Press each attenuator switch. Only the corresponding light should turn off. No other light should flicker or change status. Send a remote command to turn the attenuators off and then on. This equipment is subject to a removal agilent 11713a attenuator switch loading charge. Please Note The seller of this equipment requires the buyer to accept a sales agreement. You can rest assured that when you see the EquipNet Certified logo on a listing that you will be buying equipment that has been inspected, tested, and in many cases fully refurbished.

Keysight (Agilent) 11713A

For the best experience on our site, be sure to turn on Javascript in your browser. With a strong upward motion, lift the agilent 11713a attenuator switch ring at the top edge of the A3 latch assembly. To Replace the A3 Latch Assembly 1. Gently insert the board into the socket marked A3 latch assembly with a vertical motion.

HP Agilent Attenuator Switch Driver With GPIB 11713A 11713

Apply balanced pressure with your thumbs to push the board i nto the socket. Gently insert the board with a vertical motion i nto the agilent 11713a attenuator switch marked A4 remote local logic assembly. Apply balanced pressure with your thumbs to push the board i nto the socket 2. Replace the top cover. Remove the top cover 2. With a strong upward motion, lift the green ring at the top edge of the A5 GPI B handshake data input assembly.

AGILENT 11713A ATTENUATOR SWITCH DRIVER FOR PC

Gently insert the board with a vertical motion intothesocket marked A5 GPI B handshake data input assembly. To Remove the A6 1 nterface Assembly 1.

Remove both covers. U nscrew one screw on each cover and then si i de the cover toward the rear. Disconnect the ribbon cabiefrom agilent 11713a attenuator switch A1 interconnect assembiyto the rear panei. Remove the rear panei from the mai n frame by removi ng the four corner screws.

Agilent HP A Attenuator/Switch Driver

Remove the three screws that secure the A6 i nterface assembi y. To Replace the A6 1 nterface Assembly 1.

AGILENT 11713A ATTENUATOR SWITCH WINDOWS 8 DRIVER DOWNLOAD

No ratings or reviews yet. Thank you for allowing us the opportunity to assist with your test equipment needs.C LXI-Compliant Attenuator/Switch Driver.

The Keysight A attenuator/switch driver provides GPIB or "local" front panel drive control for programmable attenuators and electromechanical switches. Each Keysight A is supplied with two plug-in drive cables to simplify. a switching system utilizing Agilent's A attenuator/switch agilent 11713a attenuator switch. The A is capable of driving up to ten switch or attenuator sections.

Other Drivers